PX 9100 Six Zone Mixing System with Trigger-In

Feature:

• ●PX 9100 is a Six zone PA Mixer System and having TEL/EMG, 5 input, MOH output, priority control. It can extend to Zone with zone expander. With the Zone paging station it can make a call to different zone. An extra power Amplifier is needed for a working system. To build a NON interrupt BGM system then 2 amplifiers is needed.
• ●100V system.
• ●Priority function. TEL > MIC1 > MIC2>MIC3~4>PAGING>/AUX.
• ●AC or DC powered.
• ●Tabletop or System Rack-mount.

Accessory:

• ●PPS-A All-Call Microphone
• ●PPS-06 Six Zone Paging Station
• ●PPS-EX Zone Extension Station
• ●PWP-06D Six Zone Digital Wall Control Panel

Front Panel:

• ●MIC1~2 level control
• ●MIC1~2 Hi/Lo level control.
• ●MIC3~4/LINE1~2 level control.
• ●MIC3~4/LINE1~2 Hi/Lo level control.
• ●AUX1~2/Source (Wall panel) level control.
• ●AUX1~2/Source (Wall panel) Hi/Lo level control.
• ●AUX Select button (Source(Wall panel)/AUX1/AUX2)
• ●Source(Wall panel)/AUX1~2 LED indicator
• ●LCD to show information (volume)
• ●Control Button for setup the system. (Menu, +, -, ok, cancel, Reset)
• ●Up and Down button to control Master total outputs level.
• ●Priority indicator
• ●Power ON LED indicator
• ●Zone 1 & 6 LED indicator
• ●Zone 1 & 6 select button
• ●All Zone select button

Rear Panel:

• ●MOH output 1V/600ohm, 1W/8ohm, Phoenix connector.
• ●MOH output level control.
• ●TEL/EMG 1V/100V Input Phoenix connector.
• ●TEL/EMG level control.
• ●Paging Station RJ45 connector.
• ●Wall Control Panel RJ45 connector
• ●Trigger In Phoenix Connector:
  • -9 optocoupler Input, 24VDC IN
  • -1 optocoupler, PAGING Input get priority if this is shorted, 24VDC IN
  • -NC-COM-NO: Dry contact that is activated when paging.
• ●Trigger Out Phoenix Connector:
  • -10 Output, dry contact
  • -24VDC/800mA output
  • -Dry contact that will be closed in case of a fault is detected in the main unit.
• ●AMP 1~2 IN 100V, Dry contact
• ●Zone 1~6 100V output, Dry contact.
• ●24VDC In to powered the unit, Phoenix connector.
• ●MIC1: COMBI/RJ45 Balance Input with Trigger function.
• ●MIC2: COMBI Balance Input with VOX function.
• ●MIC1~2 Dipswitch for PTT/ Phantom Enable.
• ●MIC3~4: COMBI Balance Input with VOX function.
• ●MIC3~4 Slide switch for MIC/LINE sensitivity select and Phantom Enable.
• ●AUX1~2: RCA Unbalance Input.
• ●PAGING: RCA Unbalance Input.
• ●PAGING Input Level control.
• ●PRE OUT1~2: XLR Balanced, to connect to Amplifier
• ●To PEX9100: RJ45 connect to Next unit (PEX9100)
• ●CHIME VR controls chime output level.
• • -CHIME OFF/1/2/4 Tones.
  • -MICOPHONE input priority (FIFO, LIFO, MIX, OFF)
  • -Firmware upgrade Enable/Disable
  • -20kHz Pilot-tone On/OFF to monitor Amplifier errors.
  • -Mode for 1 Channel (interrupt BGM) or 2 channel mode ( NON-interrupt BGM)
• ●RS232 connector for upgrade firmware.
• ●AC Inlet
• ●AC Voltage switch
• ●Power ON/OFF switch.

Specifications: