PX 9124 Six Zone Mixing Amplifier with Trigger- In

Feature:

●PX 9124 is a Six zone PA Mixer Amplifier and having TEL/EMG, 5 input, MOH output, priority control. It can extend to Zone with zone expander With the Zone paging station it can make a call to different zone. An extra power Amplifier is needed to build a NON interrupt BGM system and have Output Power rating from 240 Watt.
●100V system.
●Priority function. TEL > MIC1 > MIC2>MIC3~4>PAGING>/AUX.
●AC or DC powered.
●Tabletop or System Rack-mount.

Accessory:

●PPS-A All-Call Microphone
●PPS-06 Six Zone Paging Station
●PPS-EX Zone Extension Station
●PWP-06D Six Zone Digital Wall Control Panel

Performance	PX 9124
Max Rated Output Power 1kHz, ≤ 1% THD	240W
Input Sensitivity & Impedance	MIC1~4 (MIC/Line1~2): 1.5mV@600Ω/200.0mV@47kΩ, Balanced AUX1~2: 200mV@10kΩ, Unbalanced PAGING IN: 200mV@10kΩ, Unbalanced TEL: 100V/100mV@600Ω, Balanced Ext Amplifier IN: 100V Dry contact
Tone Control	Bass: 100Hz , ±10dB, Treble: 10kHz , ±10dB
Frequency Response	MIC1~4/LINE: 60Hz~15kHz, +1/-3dB AUX/CD: 50Hz~20kHz, +1/-3dB TEL: 100Hz~15kHz, +1/-3dB
S/N Ratio	MIC1~4 >60dB LINE1~2 >70dB AUX1~2 >75dB TEL >70dB
Phantom Power	24V
Output	MOH Out: 8Ω/1W, 1V@600Ω PRE Out: 1V RCA Balanced Intern Amplifier Out: 70V/100V Z1~6 Out: 100V Dry contact
Trigger Out	Dry contact 24V/2A
Trigger IN	Optocoupler, max 24VDC IN
DC Out	24V/800mA
DC IN	24V/16A
Chime	OFF/1/2/4 tone
Nominal AC Line Voltage	115V/230V, 50/60Hz
Operation Temperature / Humidity	-10°C ~ +45°C @ 95% R.H. (Non-Condensing)
Storage Temperature	-20°C ~ +70°C
Dimensions (W x D x H)mm	430 x 365 x 133
Weight	21.0kg

Front Panel:

●MIC1~2 level control
●MIC1~2 Hi/Lo level control.
●MIC3~4/LINE1~2 level control.
●MIC3~4/LINE1~2 Hi/Lo level control.
●AUX1~2/Source level control.
●AUX1~2/Source Hi/Lo level control.
●AUX Select button (Source(Wall panel)/AUX1/AUX2)
●Source(Wall panel)/AUX1~2 LED indicator
●LCD to show information (volume)
●Control Button for setup the system. (Menu, +, -, ok, cancel, Reset)
●Up and Down button to control Master total outputs level.
●Amplifier overload indicator
●Priority indicator
●Power ON LED indicator
●Zone 1 & 6 output Attenuator VR.
●Zone 1 & 6 LED indicator
●Zone 1 & 6 select button
●All Zone select button
●VU-Meter

Rear Panel:

●MOH output 1V/600ohm, 1W/8ohm, Phoenix connector.
●MOH output level control.
●TEL/EMG 1V/100V Input Phoenix connector.
●TEL/EMG level control.
●Paging Station RJ45 connector.
●Wall Control Panel RJ45 connector
●Trigger In Phoenix Connector:
- -9 optocoupler Input, 24VDC IN
- -1 optocoupler, PAGING Input get priority if this is shorted, 24VDC IN
- -NC-COM-NO: Dry contact that is activated when paging.
●Trigger Out Phoenix Connector:
- -10 Output, dry contact
- -24VDC/800mA output
- -Dry contact that will be closed in case of a fault is detected in the main unit.
●Ext AMP IN 100V, Dry contact
●Int AMP Out 70/100V
●Zone 1~6 100V output.
●24VDC In to powered the unit, Phoenix connector.
●MIC1: COMBI/RJ45 Balance Input with Trigger function.
●MIC2: COMBI Balance Input with VOX function.
●MIC1~2 Dipswitch for PTT/ Phantom Enable.
●MIC3~4: COMBI Balance Input with VOX function.
●MIC3~4 Slide switch for MIC/LINE sensitivity select and Phantom Enable.
●AUX1~2: RCA Unbalance Input.
●PAGING: RCA Unbalance Input.
●PAGING Input Level control.
●PRE OUT: XLR Balanced, to connect to Amplifier
●To : RJ45 connect to Next unit
●CHIME VR controls chime output level.
- -CHIME OFF/1/2/4 Tones.
- -MICOPHONE input priority (FIFO, LIFO, MIX, OFF)
- -Firmware upgrade Enable/Disable
- -20kHz Pilot-tone On/OFF to monitor Amplifier errors.
- -Mode for 1 Channel (interrupt BGM) or 2 channel mode ( NON-interrupt BGM)
●RS232 connector for upgrade firmware.
●AC Inlet
●AC Voltage switch
●Power ON/OFF switch.